Categories: Deck cabin galley Maintenance-25
Product Short Description:

The most effective RXSOL-16-1008-060 ,Descaling Liquid - II is accomplished by circulation for large systems or components. In the case of small components, the soak method in an immersion bath can be used.

Product Description:

RXSOL-16-1008-060 Descaling Scalefoe Compound is a liquid acid containing descaling accelerators, corrosion-inhibitors and wetting agents with acidic Polymer with Phosphoric ACID.

Product Application:

FIELD :::

 

For Boilers, Condensers, etc

 

RXSOL-16-1008-060 protects efficiency of work in boilers as well where the scales are comparatively harder. Temperature of solution, while removing scales in boilers, is raised up to 70 c and the solution is circulated for 12 to 36 hours depending upon the hardness of the scales. Brushing with an iron brush gives better results in getting rid of hard scales.  ( Refer below TIPS for CLEANING )

 

 

In Melting Industry

 

RXSOL-16-1008-060 is often the automatic choice to do away with the scales from coils, cables, cooling jackets, heat exchangers or linings in steel plants. The usage of RXSOL-16-1008-060 in furnaces and steel Plants simply involves consistent circulation for 3 to 4 hour only, at room temperature.

Features, Benefits and Applications

  • Unlimited shelf life.
  • Easy to rinse off.
  • Fast and effective scale remover.
  • Removes scale and rust from condensers, evaporators, heat exchangers,Rediator etc.
  • Removes water scale from boilers.
Product Dose:

The most effective RXSOL-16-1008-060 ,Descaling Liquid - II is accomplished by circulation for large systems or components. In the case of small components, the soak method in an immersion bath can be used.

If the equipment to be cleaned is contaminated by oil, grease, sludge or carbonised oil, then pre-cleaning with Rxsol-20-2002-SC or Rxsol-10-1006-SB is necessary.

Rxsol-16-1008 should alway be used in plastic bucket. RXSOL-16-1008-060 should always be added in, never add water in RXSOL-16-1008-060.

RXSOL-16-1008-060 dilute with fresh water as 5-30%,  solution depending on scale. Make a circulation system so as to allow the solution to enter through the lowest point and leave through the highest point of the equipment, which is to be descaled.
TIPS for CLEANING 
Fill up the whole system with the solution and circulate through a centrifugal pump.
At the initial stages, pH of the solution is generally at 2 to 3 there is an increase in the pH of the solution, during the reaction. The increase in the pH of the solution during circulation reflects on going reaction. Add more quantity of RXSOL-16-1008-060 and continue circulation, in case of the pH level being 4.5 to 5.  If circulation of the system shows constant pH 2 to 3 after time confirms the completion of the process of descaling.

The process of descaling is checked by a periodical pH testing of the solution.
 

For silica scales and very hard scales, power and liquid forms of RXSOL-11-1102-025 is recommended.

For the prevention of further scaling in melting industry, RXSOL-16-1056-025 is recommended.

 

NOTE: After using RXSOL-16-1008-060 ( After completion of descaling ) rinse all equipment and metal surfaces at least one time with a 0.5% solution of RXSOL-20-2059-025 in fresh water. This solution should be circulated for 2-4 hours or until pH value comes 6-7. This will neutralize any remaining acid and passivate steel surfaces.

Product Note:

Why Use RXSOL Descaler?

  • It is a safe , economical concentrated  chemical to be used on the waterside of heat transfer equipment.
  • You do not have to heat RXSOL 1008 .
    RXSOL 1008  is safer for the employees to use than other acid products.

  • Your equipment will be cleaned in only hours without disassembling any part of the equipment. Equipment can also be cleaned without any down time (cleaning on the run).

  •  Cleans down to the original surface without pitting.
  •  RXSOL 1008 is safe on copper, copper-nickel, bronze, brass, iron, stainless steel and rubber.
  •  RXSOL 1008  will extend the usable life of your equipment, especially when used as a part of a regularly scheduled preventative maintenance program.
  •  Removing the scale build-up allows your equipment to operate more efficiently with less downtime.
Free Delivery / Supply Locations : 
Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Ras al Khaimah, Fujairah, Sharjah, Umm Al Quwain, Fujairah, Ruwais, Mina (Port) Zayed, Khalifa Port, Kizad, Port Rashid, Jebel Ali Port, DP WORLD, Jebel Ali Free Zone, Khor Fakkan Container Terminal, Port Rashid, Jebel Ali Port, Mina Kalid Port, Khor Fhakan Port ( Khawr Fakkan, Khawr al-Fakkan ), Sharjah Creek, Ajman, Port of Hamriyah, Mina Zayed Port, Mussafah port, Khalifa Port, Umm al-Nar Port, Um Al Quwain Port, Saqr Port, Port of Fujairah, Dibba Port, Jebel Dhanna, Mina Al Hamriya, Mina Rashid, All United Arab Emirates