Your shopping cart is empty.
Very power full superior product which making the film to protect the Corrosion and antiscalant in Pipe line and equipment where supplies hot and cold water.
Antiscalant C.I ALKA is very power full superior product which making the film to protect the Corrosion and antiscalant in Pipe line and equipment where supplies hot and cold water.
RO antiscant
Scaling is caused in membranes because the level of hardness salts in the water becomes highly concentrated as it passes through the RO unit. In smaller units scale formation can be prevented by base exchange softening the make-up water but for larger systems that is very expensive. We have developed a range of easy to handle, cost effective RO Antiscalant which increase the solubility of the hardness salts so they remain in solution rather than forming scale on the membrane. Our cost effective RO antiscalants will inhibit a wide range of foulants including: calcium carbonate, calcium sulphate, barium sulphate, strontium sulphate, calcium fluoride, silica and iron.
RO Antiscalants are dosed directly to the RO feed water tank or feed water line (after pretreatment) at the recommended dosage of 1-3 mg/L and maximum dosage at 8mg/L, subject to inlet water quality and parameters is respect of Calcium Hardness, Iron, TDS, Alkalinity, pH and silica content. Maximum dilution should be 10% with RO or DI water for temperature less than 30 deg C. For higher temperature the dilution ratio can increase.
Key Features and Benefits
Our RO Antiscalant (HIGH PH) is a super-threshold RO membrane antiscalant and antifoulant which is able to stabilize a wide range of supersaturated salt solutions, thereby preventing the precipitation on the membrane surface.
It reduces the risk of scaling and eliminates the use of hazardous acids,resulting in efficient plant operation with highest possible conversion rate.
It is a very effective antiscalant . It is also compatible with RO CHEMICALS series of coagulant and flocculants (polyelectrolytes). Our RO Antiscalant (HIGH PH) is effective in minimizing scaling in presence of foulants like Calcium Carbonate, Sulfate salts of Calcium, Barium, Strontium and Magnesium, Calcium Fluoride, Iron and Silica.
Key Features and Benefits
Application and Dosage
Our RO Antiscalant (HIGH PH) is dosed directly to the RO feed water tank or feed water line (after pretreatment) at the minimum recommended dosage of 1ppm and maximum dosage at 15ppm, subject to inlet water quality and parameters is respect of Calcium Hardness, Iron, TDS, Alkalinity, pH and silica content.
In case of high iron content of about 0.5 to 1.0ppm, the dosing has to be increased by 10-15ppm for stabilizing Calcium.
At about 10-15ppm dosage our RO Antiscalant (HIGH PH) is capable of fully inhibiting iron and calcium, and silica up to 166ppm. For higher silica content RXSOL ANTISCALANT should be used.
Antiscalant RO RXSOL-33-3302-025
Antiscalant C.I ALKA RXSOL-33-2034-025
Membrane Antiscalant ALKA 191T RXSOL-33-3321-030
Antiscalant ORG EV 2030 RXSOL-33-3325-230
Antiscalant RXSOL ORG EV RXSOL-33-3327
Antiscalant C.I ALKA is a special formulated Product by liquid silicate and inorganic polyphosphates can Food that is used in the treatment of fresh hot and cold water, for protect the corrosion and scale deposit in Pipe line and Equipment. This significantly reduces the corrosion which caused by aggressive water and promotes the formation of a protective film. Prevents the precipitation of calcium and magnesium in water.
For natural waters "normally mineralized" (up to 500 mS / cm). Recommended starting dose of 40 g / m, after the formation of protective film is sufficient.
A maintenance dose of 20 g / m³.
With salt water is very necessary to increase the dose above which can reach, in the case brackish water, even up to 200 g / cm.