Categories: RIGS Oil Field-34
Product Short Description:

Powerful concentrated corrosion inhibitor acts as oxygen scavengers used to effectively remove dissolved OXYGEN

Product Description:

This is most common oxygen treatment as a scavengers used to effectively remove dissolved  OXYGEN from your feedwater. By the presence of dissolved oxygen in system, corrosion and pitting caused on metal surface. Removes dissolved oxygen, By acting as an oxygen scavenger.

A fast-acting, catalyzed sodium sulphite (Na₂SO₃) oxygen scavenger for low- and medium-pressure boiler systems. The product reacts stoichiometrically with dissolved oxygen to prevent corrosion in boilers, feed lines, and condensate systems by converting oxygen to inert sulfate.

Product Application:

Key Areas of Application of Oxygen Scavenger OxyGuard-S

  • Oxygen removal in low/medium-pressure boilers (typically up to ~65 bar; usage above this pressure is uncommon due to potential sulfate/solids carryover).
  • Hot standby protection to prevent pitting during idle periods i.e. Oilfield Application.
  • Feedwater & deaerator outlets where residual O₂ must be suppressed rapidly.
Product Dose:

Reaction (overall):
Na₂SO₃ + ½ O₂ → Na₂SO₄

Catalyst accelerates the reaction at lower temperatures and shorter residence times (e.g., in deaerator outlets and feedwater lines)

Power of Oxygen Scavenger OxyGuard-S: powerful stoichiometry: ~7.88 mg/L Na₂SO₃ per 1 mg/L dissolved O₂.

With safety factor (process variability, kinetics), dose 10–12 mg/L Na₂SO₃ per 1 mg/L O₂.

 

Typical operating targets (LP/MP boilers):

 

  • Deaerator outlet O₂: ≤ 7–10 ppb (if DA present)
  • Sulfite residual in boiler water:
  • Normal operation: 20–40 mg/L as Na₂SO₃
  • High risk / wet lay-up: 60–100 mg/L as Na₂SO₃
  • pH (feedwater/boiler): follow your internal treatment program (commonly FW pH 8.5–9.2; boiler water pH 10.5–11.5 depending on pressure).

 

Where to feed:

  • Preferably deaerator storage section or feedwater line upstream of economizer to ensure complete O₂ removal before the boiler.

Example Dose Calculation

Feedwater DO = 0.10 mg/L (100 ppb) at 20 m³/h.
Stoichiometric Na₂SO₃ = 0.10 × 7.88 = 0.788 mg/L.
With 1.3× safety factor → ~1.0 mg/L Na₂SO₃.
At 20 m³/h → 20 g/h Na₂SO₃ (as pure).
Using 38% liquid: 20 / 0.38 ≈ 52.6 g/h (~40 mL/h) (SG 1.32 ⇒ ~30 mL/h by mass; verify on site).
Fine-tune to maintain target sulfite residual in boiler.

Product Note:

Benefits of using Oxygen Scavenger OxyGuard-S

  • Rapid kinetics with catalyst—effective even at moderate temperatures.
  • Reliable corrosion protection of pre-boiler & boiler circuits.
  • Cost-effective vs. volatile scavengers for LP/MP systems.
  • Easy control by simple sulfite residual testing.
  • Compatible with most phosphate/polymer internal treatments.
Free Delivery / Supply Locations : 
Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Ras al Khaimah, Fujairah, Sharjah, Umm Al Quwain, Fujairah, Ruwais, Mina (Port) Zayed, Khalifa Port, Kizad, Port Rashid, Jebel Ali Port, DP WORLD, Jebel Ali Free Zone, Khor Fakkan Container Terminal, Port Rashid, Jebel Ali Port, Mina Kalid Port, Khor Fhakan Port ( Khawr Fakkan, Khawr al-Fakkan ), Sharjah Creek, Ajman, Port of Hamriyah, Mina Zayed Port, Mussafah port, Khalifa Port, Umm al-Nar Port, Um Al Quwain Port, Saqr Port, Port of Fujairah, Dibba Port, Jebel Dhanna, Mina Al Hamriya, Mina Rashid, All United Arab Emirates